admin

06.07.2022 - 19:48

What does aq stand for in chemistry?

Question:

What does aq stand for in chemistry?

Answers (1)

Bowen April 10, 2023 в 16:52

AQ stands for aqueous, which refers to a solution in which the solvent is water. This term is commonly used in chemistry to indicate that a substance is dissolved in water. In chemical equations, the symbol (aq) is added to the name of a dissolved substance to indicate its aqueous state.

Do you know the answer?

Leave a comment Cancel Response

Not sure about the answer?

Find the right answer to the question What does aq stand for in chemistry? by subject Chemistry, and if there is no answer or no one has given the right answer, then use the search and try to find the answer among similar questions.

Search for other answers

New questions in the category: Chemistry

An open box is to be made from a 3ft by 8ft rectangular piece of sheet metal by cutting out squares of equal size from the four corners and bending up the sides. Find the maximum volume that the box c

Gold ore typically contains 10 grams of gold per 1000 kilograms of ore, and the current value of gold is $1185 per ounce. What mass of ore in tons (1 ton = 2000 pounds) must be refined to obtain $1 million worth of gold?

Following the Procedure of this experiment, a student titrated 0.653 g of an unknown weak, monoprotic acid with 0.100M NaOH and monitored the titration with a pH meter. Her titration data were: Volu

Calculate the pH of a 0.42 M solution of sodium acetate, CH3COONa. (Ka(acetic acid) = 1.8 * 10-5)

Find the pH of a buffer that consists of 0.12 M boric acid and 0.82 M sodium borate. (pKa of boric acid = 9.24)

If the price of electrical energy is $0.10 /KWh, what is the cost of using electrical energy to heat the water in a swimming pool (12.0space m times 9.00 space m times 1.5space m) from 15 ^oC to

During lab, students mixed two solutions of soluble ions in a ceramic well to determine if a precipitate forms. Write the dissolution reaction for the ionic solids below. (Use the lowest possible coe

Mantles for gas lanterns are made of thorium, because it forms an oxide that can survive being made incandescent for long periods of time. Natural thorium is almost 100% 232Th, with a half-life of 1.4

Consider three engines that each use 1650 J of heat from a hot resevoir (temperature = 550 K). These three engines reject heat to a cold resevoir (temperature 330 K). Engine I rejects 1270 J of heat.

In a steam power plant, 1MW heat is added in the boiler at 700 o C, 0.58 MW heat is taken out in the condenser at 40 o C, and the pump work is 0.02 MW. a) What is the work (in MW) of the turbine in

What is the pH of a 1.5 M solution of trifluoroacetic acid (CF3CO2H) with pKa = 0.2?

A forensic scientist is given a white substance that is thought to be cocaine. The substance is found to have a percent composition: 49.48% C, 5.19% H, 28.85% N, and 16.48% O. What is the empirical f

Aluminum oxide (used as an adsorbent or a catalyst for organic reactions) forms when aluminum reacts with oxygen 4Al(s) + 30_2(g) rightarrow 2A1_20_3(s) A mixture of 200.7 g of aluminum (M = 26.98 g/m

Using 1 mL is 0.034 fl oz, how do you convert 8 milliliters to fluid ounces?

What type of reaction occurs in CCA (Chromated Copper Arsenate) Is it a Redox?

A student fails to insert the cuvette into the colorimeter or spectrophotometer correctly. What effect will this have on the measured absorbance?

Look up the p K b of aneline in aqueous solution. Discuss what the value means in terms of the base strength of aniline in water. Will aneline appear to be a stronger or weaker base in acetic acid as a solvent compared to water as a solvent? Explain.

Tina, the titrating student, did not completely dissolve her antacid tablet prior to beginning the titration and still had some chunks of tablet in her solution at the end of her titration. How would this affect her results (i.e. would the calculated mass

An alloy of iron and carbon was treated with sulfuric acid, in which only iron reacts. 2Fe(s) + 3H_2SO_4(aq) to Fe_2(SO_4)_3(aq) + 3H_2(g) If a sample of alloy weighing 2.358 g gave 0.1067 g of hydrogen, what is the percentage of iron in the alloy?

Calculate the molarity and normality of the following solutions: a. 1.67% w/v acetic acid b. 20 g/L tartaric acid c. 2.95 g/L malic acid

Authorization

Password generation