Analytical chemistry

admin

04.07.2022 - 23:30

How can the concentration of a solution be increased?

Question:

How can the concentration of a solution be increased?

Answers (1)

Dorotha April 16, 2023 в 23:04

The concentration of a solution can be increased by either adding more solute to the solvent or removing some of the solvent. When more solute is added, the amount of solute molecules in the solution increases, causing the concentration to increase. On the other hand, if some of the solvent is removed, the solute becomes more concentrated in the remaining solvent, leading to an increase in concentration. This process is commonly referred to as evaporation or distillation, where the solvent is heated and vaporized, leaving behind a more concentrated solution.

Do you know the answer?

Leave a comment Cancel Response

Not sure about the answer?

Find the right answer to the question How can the concentration of a solution be increased? by subject Analytical chemistry, and if there is no answer or no one has given the right answer, then use the search and try to find the answer among similar questions.

Search for other answers

New questions in the category: Analytical chemistry

What happens to recrystallization if a large excess of decolorizing charcoal is used?

How to prepare 50 % of sulphuric acid from 10 N of sulphuric acid?

The EPA’s secondary standards for contaminants that may cause cosmetic or aesthetic effects in drinking water suggest an upper limit of 0.300 mg/L for iron. If 2.96 x 104 liters of water in a storage tank contains 26.8 grams of Fe, what is the contaminant

How many mL of acetone are required to make an 8.42 % v/v aqueous solution in a 300 mL volumetric flask?

How much water should be added to 1 gallon of pure antifreeze to obtain a solution that is 5% antifreeze?

How much water must be evaporated from 32 ounces of a 7% salt solution to make an 8% salt solution?

An aqueous solution of 0.216 M sodium phosphate for an experiment in lab is needed, using a 300 mL volumetric flask. How much solid sodium phosphate should you add?

What is conductivity in analytical chemistry?

What molarity (M) is 0.9% glucose (MW = 180) solution?

Most intravenous (IV) solutions used in hospitals are isotonic solutions, which exert the same osmotic pressure as body fluids such as red blood cells (RBCs). Two common isotonic IV solutions are 5.0% (m/v) glucose or 0.9% (m/v) NaCl (glucose is 180.156 g

A flexible 1L “bag” of intravenous saline solution is more accurately described as 0.9% sodium chloride (w/v) in water. How many grams of sodium chloride are in the 1L bag? What is the molarity of the sodium chloride solution, expressed in mmol/L? What is

How can nitrogen and oxygen be separated?

What is wet sieving in chemistry?

What is gravimetric analysis in analytical chemistry?

A 100.0-g sample of industrial wastewater was determined to contain 0.96 mg of mercury. Express the mercury concentration of the wastewater in ppm. a. 9600 ppm b. 96 ppm c. 9.6 ppm d. 0.96 ppm

Convert 8/12 to a percent.

In a solution of 30% ethanol and 70% water, what is the solute and what is the solvent?

Concentrated hydrochloric acid is an aqueous solution that is 37.2 % HCl. The density of the solution is 1.19 g/mL. What mass of HCl is contained in 0.683 L of solution? Give your answer as a whole number.

a) The normal creatinine levels in adults are 0.6-1.2 mg/dL. If a 5.0-mL sample contains 45 mu g of creatinine, is that within the normal range? b) Creatinine has a molar mass of 113.5 g/mol. What is the molarity of creatinine in the patient’s sample in

What are the parameters of TLC, HPLC, and CC? Briefly describe the relationship between them.

Authorization

Password generation